Seven Measurement Mistakes That Cost Fabricators a Remake

Nearly every remake in window and door fabrication starts at measurement. These are the seven that recur, and the habits that prevent them.

A remade sliding window costs the material, the labour, a week of the customer's patience and usually the next job they would have given you. Almost none of them are caused by bad fabrication. They are caused by a number written down wrong, read wrong, or never written down at all.

Here are the seven that recur, in roughly the order they show up.

1. Measuring in one place

Old masonry is not square. An opening can be 48 inches at the top and 46 at the bottom, and if you measured the top you have a frame that will not go in.

The habit: width at top, middle and bottom. Height at left, middle and right. Six numbers, ten seconds. Take the smallest and write down that you did.

2. Measuring the brickwork when plaster is still to come

An unplastered opening is typically three quarters of an inch to an inch larger per side than the finished one. Measure it before the plaster and your frame is loose; measure it after and it is right.

The habit: record the state of the opening on the sheet — "plaster pending, both sides" — and either go back or deduct deliberately and note the deduction.

3. Writing it on whatever was in the van

A cigarette packet, the back of an old invoice, a palm. Every one of these has produced a window at the wrong size, usually because a 7 was read as a 1 or because the sheet was lost between the site and the workshop.

The habit: one structured sheet per site, one row per opening, filled in at the site rather than from memory afterwards. Typed is better than written, because typed has no handwriting.

4. Not recording which opening is which

Five windows, five sets of dimensions, no locations. In the workshop they are five identical-looking frames and the 48×48 that was meant for bedroom one goes to bedroom two, where the opening is 52.

The habit: every row gets a location in plain words, and the frames get marked with it before they leave.

5. Forgetting that the floor is not finished

For doors in particular. Measure to the bare slab, and once the tiles and the bed go down, the door fouls. Twenty millimetres of tile and adhesive is enough.

The habit: ask what the finished floor level will be, and record both the current and the finished level for every door.

6. Never comparing the measured size against the quoted size

This is the expensive one. You quoted from an estimate taken in five minutes at the first visit; the real measurement is taken three weeks later by somebody else. If nobody puts the two numbers side by side, a difference that should have been a revised quotation becomes either a remake or free work.

The habit: the measurement sheet shows the quoted dimensions and the actual ones in adjacent columns, and the revised total area at the bottom. If the area grew, that is a revision to send before fabrication starts, not a gift.

7. Letting the customer measure

It happens, usually to save a visit on a small job. The customer measures the sash instead of the opening, or the inside of an existing frame they intend to remove, and you fabricate to a number nobody from your shop ever checked.

The habit: if you genuinely cannot visit, make the customer's figures provisional in writing, and say in the quotation that the order is subject to site measurement. Then actually do one before cutting.

The allowances nobody should automate

Every system has its own deduction for fixing clearance, and it depends on the frame, the packing, the sealant gap and whether you are fixing into masonry or a sub-frame. Software that silently subtracts a standard number from your measurement is more dangerous than software that subtracts nothing, because you stop checking.

Record what you measured. Apply your own deduction consciously, every time, and write down which one you used.

The five-minute discipline that prevents most of this

Before you leave site, read the sheet back opening by opening while standing in the property. Count the rows against the rooms. Check the total area against the quoted area. If either is off, you are standing in exactly the right place to fix it, which you will not be tomorrow.

Further reading

How to quote aluminium windows · Paper vs software in a small shop · A measurement sheet that does this

Get Expert Installers for Seven Measurement Mistakes That Cost Fabricators a Remake
Share your requirement — we connect you with trusted, verified installers.
A free client account is created for you automatically — login details are emailed so you can track your requirement.

Looking for professional installation services?

Find Installers Register as Installer